Heat pumps

Heat pumps for Seattle homes, priced before anyone visits.

Ducted heat pumps, dual fuel with a gas furnace as backup, and ductless. Installed by our own crew in Seattle and King, Snohomish and Pierce counties. Most systems $13,700 to $27,400 installed, with sales tax.

Day & Night Elite Dealer · Mitsubishi Electric Diamond Contractor

Installed prices

All-electric heat pumps, three tiers.

The smallest system in each series, installed and permitted, with sales tax. Your house sets the size, and the instant estimate prices yours.

Essential

Day & Night Performance single-stage heat pump

From $14,300installed, with sales tax

Single-stage, with a matching air handler. A straightforward all-electric replacement.

Advanced

Day & Night Performance two-stage heat pump

From $18,900installed, with sales tax

Two-stage, so it runs on low most of the time: quieter, steadier temperatures, lower bills.

Ultimate

Day & Night Ion variable-speed heat pump

From $27,400installed, with sales tax

Fully variable speed. Runs as low as 55 decibels outdoors, and the labor warranty matches the factory warranty.

Keep your furnace as backup

A heat pump with a new high-efficiency gas furnace for the coldest nights starts at $16,900 installed. Adding a heat pump to a furnace you keep starts at $9,900.

No ducts?

Ductless heat pumps start at $7,500 for one room. Ductless prices

Why heat pumps fit Seattle

Seattle winters are long and mild, which is where a heat pump does its best work: it moves heat instead of burning fuel, so most of the year it delivers several units of heat for each unit of electricity. Cold-climate models keep heating well below freezing, and you can keep a gas furnace as backup for the coldest nights or go all-electric.

The same system cools the house in the heat weeks, which matters more every summer, and with sealed returns and MERV 13 filtration it helps in smoke season too.

What the price includes

  • A 3D scan and a room-by-room load calculation. We scan the house with LiDAR (Conduit Tech) and build an ACCA Manual J from the scan, so the system is sized to your house's heat loss, not matched to the old unit.
  • Installation by our own crew. Permit, startup and inspection every time.
  • Electrical. A fused disconnect with surge protection; panel work is designed in the proposal, not a surprise on install day.
  • Thermostat. Thermostats and thermostat wiring are priced separately.
  • Warranty. 2-year labor on Essential and Advanced. Ultimate's labor warranty matches the factory warranty, and top-of-the-line Day & Night equipment carries a 12-year No Hassle Replacement.

FAQ

Heat pump questions

Will a heat pump keep my house warm in a cold snap?

Yes. Cold-climate heat pumps keep heating well below freezing. If you heat with gas now, we often recommend a heat pump with a new high-efficiency furnace as backup for the coldest days; the instant estimate prices both.

Will it be loud?

Not very. Day & Night's Ion variable-speed heat pump runs as low as 55 decibels outdoors, and Mitsubishi Hyper-Heat outdoor units as low as 54. We place and mount outdoor units for your lot, not where the old unit happened to sit.

Are there rebates?

Seattle City Light, PSE, Snohomish PUD and Tacoma Power each run heat pump rebates with their own equipment and contractor rules, and income-qualified homes may qualify for Washington's HEAR rebate. The federal heat pump tax credit ended for systems installed after December 31, 2025. We confirm what your address qualifies for and file the paperwork with you.

How long does an install take?

1 to 3 days for most systems. We cover floors, clean up daily, and leave the permit record with you.

How long is your labor warranty?

Essential and Advanced systems include a 2-year labor warranty. On Ultimate, our top tier, the labor warranty matches the factory warranty on that equipment: 5, 7, 10 or 12 years.

Who comes out for the design consultation?

Devan Amling, our Director of Operations, or one of our senior Design Consultants. They scan the house in 3D, build a room-by-room ACCA Manual J load calculation from the scan, check the ducts and electrical panel, and you get a firm price that holds for 30 days. Alex Yi, the owner, reviews every design before you see a price.

How do you size the system?

From a 3D scan, not a rule of thumb. We scan your house with a LiDAR scanner (Conduit Tech) and build an ACCA Manual J load calculation from the scan, room by room. Most quotes are sized by square footage or by matching the old unit. An oversized system short-cycles, runs louder and wears out sooner; an undersized one can't keep up in a cold snap.

See your price in about a minute.

Answer a few questions about the house and see installed prices for three real systems, with sales tax.

See my price